[ Chinese wardrobe network ] In today's wardrobe market, the overall wardrobe continues to heat up, and is loved by consumers. However, consumers often have doubts about how to choose a wardrobe. Therefore, we start from the three aspects of the panel, edge banding and veneer of the wardrobe to teach consumers how to identify inferior wardrobes.
Wardrobe experts teach you three tricks to see the quality wardrobe
The first trick to see the inferior wardrobe: whether the wardrobe sheet is environmentally friendly
The formaldehyde content of the board is the primary factor to consider when purchasing a wardrobe, as this is closely related to our health. When shopping, consumers can close the door and wait for about 5 minutes, then yank open the door and smell the nose with no smell. There is an odor indicating that the formaldehyde content may exceed the standard and is a poor quality product.
The second measure of seeing the inferior wardrobe: whether the wardrobe is tight
Some manufacturers have no professional equipment, and the production of the wardrobe products is rough, and there are obvious edge collapses around them. Some even cut corners and cut only the front side of the board. The unsealed surface easily absorbs moisture from the air, causing the sheet to swell, causing the wardrobe to deform and affecting the service life. Professional manufacturers use precision panel saws to cut sheets without cracking around the sheets. After sealing around, it can effectively prevent the moisture in the air from intruding into the interior of the board.
The third measure of seeing the inferior wardrobe: whether the wardrobe veneer is wear-resistant
Professional manufacturers use environmentally-friendly melamine veneers treated with high temperature and high pressure, with high surface strength, abrasion resistance and scratch resistance. Some manufacturers produce inferior wardrobes, which are made of low-cost panels on the market. The surface is covered with Pauli paper sheets. It looks good. In fact, the anti-staining and abrasion resistance is poor. Scratches, surface stains are not easy to clean.
From the panel of the wardrobe, veneer, edge banding, backboard structure, hardware accessories, anti-counterfeiting marks, and matching, we will identify the wardrobe.
1, look at the board of the wardrobe
Professional manufacturers use all the plates that meet the national testing standards. Non-professional manufacturers choose some non-test reports, which have certain potential threats to human health. Therefore, to buy a wardrobe, it should be seen whether the manufacturer has a plate inspection report and relevant testing certificate from the national authority inspection department.
2, look at the wardrobe sheet veneer
Some wardrobes look good on the surface, but they can be scratched with a light stroke. These closet panels use low-priced styrofoam on the market. This paper looks good but has poor abrasion resistance. The professional manufacturers generally use melamine dipped paper and are treated by high temperature and high pressure, with high environmental protection coefficient, high surface strength, abrasion resistance, scratch resistance and anti-fouling.
3, look at the edge of the wardrobe sheet
Professional manufacturers use precision panel saws to cut the board, and there is no chipping around the board, because it can effectively prevent the moisture in the air from invading the inside of the board. Some manufacturers do not have professional equipment, the cutting is rough, and there is obvious chipping around.
4, look at the wardrobe back panel structure
Professional manufacturers adopt a recessed structure to prevent the back plate from directly contacting the wall to absorb moisture on the wall. Some brands have thin back plates and are connected by nail-type back plates. The back plates are in direct contact with the wall. The moisture on the wall is easily absorbed by the plates, which is easy to get wet, moldy and deformed, and the cabinet loses its seal. Sex.
5, look at the wardrobe hardware accessories
Professional manufacturers use famous factory accessories, quality assurance. Accessories are often hidden, consumers are difficult to identify, and you have to carefully push and pull. Hardware accessories are a very important element of wardrobes, bookcases and sliding doors. They are an important indicator for ensuring the comfort and durability of household products.
6, look at the manufacturers anti-counterfeiting signs and services
Professional manufacturers have obvious anti-counterfeiting labels on the surface of the wardrobe or the edge banding, cabinet door profiles and pulleys. Quality and maintenance are guaranteed, and consumers can use it with confidence.
7, look at the matching and systematic of furniture
Professional panel furniture manufacturing enterprises can not only make wardrobes, cloakrooms, bookcases, but also provide system home furnishing products such as shoe cabinets, wine cabinets, beds, dressing tables and bedside tables.
The whole wardrobe is very popular because it is environmentally friendly, durable, beautiful, saves space, and the purchasing method is relatively simple. As long as you read the above precautions, you can buy a good wardrobe that suits you.
Traffic signs are road facilities that use words or symbols to convey guidance, restriction, warning or indication information. In traffic signs, it is usually an important measure to implement traffic management and ensure road traffic safety and smoothness by setting eye-catching, clear and bright traffic signs.There are many types of traffic signs, which can be divided into main signs and auxiliary signs in various ways.Movable marks and fixed marks;Lighting signs, luminescent signs and reflective signs;And variable information signs that reflect the changing driving environment.
Road Sign Boards,Road Sign Traffic,Warning Traffic Sign,Aluminum Traffic Sign
Chengdu GodShape Sign Co., Ltd , https://www.signsgs.com