The quality of wood determines the quality of solid wood furniture, then

Solid wood furniture refers to pure solid wood furniture, which means that all materials are natural materials that have not been reworked. Furniture without any wood-based panels is used, because there are no two identical trees, two identical materials, so each A product will have its unique characteristics;

The natural properties of wood, such as mineral lines, color and texture changes, needle joints, resin pouches and other natural imprints, make furniture more natural and aesthetic. At the same time, the quality of wood is also an important factor in determining the quality of solid wood furniture, then what factors will affect the quality of wood?

1 external factors

temperature

Temperature is a major factor affecting the drying rate of wood. When the temperature rises, the water pressure in the wood increases, and the viscosity of the liquid free water decreases, which is conducive to promoting the flow and diffusion of moisture in the wood; the drying capacity of the copper wire drying medium is increased, and the evaporation rate of the surface moisture of the wood is accelerated. However, it is worth noting that if the temperature is too high, it will cause cracking and deformation of wood, reduce mechanical strength, discoloration, etc., and should be properly controlled.

humidity

Relative humidity is an important factor affecting the drying speed of wood. In the case of the same temperature and airflow speed, the higher the relative humidity, the greater the partial pressure of water vapor in the medium, and the more the water on the surface of the wood is less likely to evaporate into the medium, the slower the drying speed;

When the relative humidity is low, the surface moisture evaporates quickly, the surface water content decreases, the water content gradient increases, the water diffusion increases, and the drying speed is fast. However, if the relative humidity is too low, cracking and drying defects such as honeycombs may occur or even worsen.

Air circulation speed

Air circulation speed is another factor that affects the drying speed of wood. The high-speed airflow can destroy the saturated vapor boundary layer on the surface of the wood, thereby improving the heat transfer and mass transfer conditions between the medium and the wood, and accelerating the drying speed.

For difficult dry materials or when the moisture content of wood is low, the moisture movement inside the wood determines the drying speed; it is not practical to increase the evaporation rate of surface moisture by increasing the flow rate of large medium, but it will increase the water content gradient and increase the drying. The danger of defects. Therefore, difficult materials do not require a large media circulation speed. The above three factors are external factors that can be artificially controlled, and are properly controlled to accelerate the drying speed while ensuring the quality of wood drying.

For example, when dry softwood or soft hardwood sheet is used, the moisture inside the wood is easy to move, and the dry bulb temperature, the medium humidity can be lowered, and the gas flow circulation flow rate can be increased to accelerate the drying speed;

However, when drying mahogany wood or slabs, lower temperatures, higher humidity and lower air circulation speeds should be used to avoid drying defects.

2 intrinsic factors

Wood species and structural features

The wood of different tree species has different structures, and the size and number of pits and the size of micropores on the pit membrane are very different. Therefore, the difficulty of water movement along the above path is different, that is, the wood species are affected. The main internal cause of drying speed.

Due to the large number of fillings in the cavities and pits of the hard-boiled hardwood (such as rosewood) and the small diameter of the micropores in the perforated membrane, the drying speed is significantly smaller than that of the loose-leaved broad-leaved trees; in the same tree species, the density increases. The resistance of water flow in the large capillary tube increases, the water diffusion path in the cell wall is prolonged, and it is difficult to dry.

Wood thickness

The conventional drying process of wood can be approximated as a one-dimensional heat and mass transfer process along the thickness direction of the material. The thickness increases, the heat and mass transfer distance becomes longer, the resistance increases, and the drying speed decreases significantly.

Wood moisture content

Under the fiber saturation point, as the water content decreases, the lateral diffusion coefficient of the sorbed water decreases, while the diffusion coefficient of water vapor in the cell cavity increases, due to the proportion of water vapor diffusing in the cell cavity during drying. It is not large, and the lower the water content, the longer the water diffusion path, so the lower the water content, the more difficult it is to dry.

Wood heart sapwood

There are many inclusions in the heartwood cells of broad-leaved trees, and most of the pits in the heartwood of conifers are occluded, so the heartwood is more difficult to dry than the sapwood.

Wood texture direction

Wood ray is good for moisture conduction, and the moisture conduction in the radial direction of the wood is about 15%-20% larger than the chord direction. Therefore, the string cutting board usually has a faster drying speed than the diameter cutting board.

Although the internal factors cannot be controlled, as long as the characteristics of the wood are used to make good use of the drying equipment and technology, the drying speed can be increased, the unnecessary loss can be reduced, and the drying effect can be improved while maintaining the wood properties.

Stainless Steel Bbq Grill

Hello, grid charcoal roast *, in addition to baking, but also to prepare smoke-free special charcoal. In addition to the fire burning charcoal, in the barbecue process to continue to add charcoal to maintain the heat. Although this method can sometimes be "angry" and may even make people angry at other times, it is closer to nature and the food cooked by charcoal at high temperature will have a special fragrance. Charcoal grilling definitely tastes better than electric grilling, and it feels different. Electric grilling is just not that strong. However, there are many things to prepare for charcoal barbecue, and it is easy to get dirty. If you don't care about these, it is also very good to get a charcoal barbecue. If it is used at home, of course, the electric barbecue is convenient and clean. But if you want taste and fun, or charcoal is better.

Packing

Packing will by carton.

Stainless Steel Bbq Grill,Steel Grill,Stainless Steel Grill,Stainless Steel Bbq

Henan Jinbailai Industrial Co.,Ltd , https://www.designsteelarts.com