Baby strollers also have national standard seat belts that are not bought in China. Although there are no detailed statistical data in this regard. However, according to the U.S. childcare magazine, more than 10,000 children in the United States are injured each year because of strollers.
Industry sources told reporters that young parents need to pay attention to the following points when selecting a stroller: First, check whether the opening of the stroller is convenient, check the seat belt and the locking and safety devices. The safety belt requirements for strollers in the national standards are as follows: The upper side is 180mm higher than the seat cushion, and the minimum widths of the shoulder strap, the fork strap and the hip belt are respectively 15mm, 20mm and 50mm.
Secondly, the depth between the stroller seat pocket and the armrest should be at least 180mm. The seat pocket is too shallow and the child's center of gravity will shift when turning or twisting in the car, which will easily cause a roll-over accident.
Finally, experts advise that a safe stroller should first have shoulder straps, belts, and chin straps, and it is best to choose four-wheel locks. When using, do not hang objects on the handle so as not to make the body unstable.
(Buy baby stroller, baby carriage wholesale, sales, find China Baby Vehicle Industry Network /, Tel 0551-82363313)
Of the world's steel, 60 to 70% are sheets, most of which are stamped into finished products. The car body, chassis, fuel tank, radiator fins, boiler drums, container shells, motors, laminations, etc, are all stamped and processed. There are also a large number of Stamping Parts in products such as instruments, household appliances, bicycles, office machinery, and living utensils.
Compared with castings and forgings, stamping parts have the characteristics of thinness, uniformity, lightness, and strength. Stamping can produce workpieces with reinforcing ribs, ribs, undulations, or flanges that are difficult to manufacture by other methods to improve their rigidity. Due to the use of precision molds, the precision of the workpiece can reach the micron level, and the repeatability is high.
Stamping is an efficient production method. Using compound dies, especially the progressive die, multiple stamping processes can be completed on one press. Generally, hundreds of pieces per minute can be produced by high production efficiency, good working conditions, low production cost.
Here are a few stamping parts manufactured by our company.
1. Sheet Metal Threaded Nut
The part is stamped from the cold-rolled steel sheet. The middle hole is threaded, the surface is electroplated. It acts as a nut during use and is used on occasions where the force is not too heavy. The cost of this part is lower than that of ordinary hexagonal nuts, and the weight is lighter than that of hexagonal nuts too. This part is often used in household products. If you need this type of part, please feel free to contact us. We can customize the parts according to customer requirements.
2. Contact Plate for Battery
This contact plate is used on almost all occasions where there are batteries. This part is a square piece with protrusions, which is the contact position of the battery. The parts have no burrs. All sharp corners were eliminated. The surface is high-gloss and bright. The part is stamped from the brass sheet. The surface is electroplated to prevent oxidation. Our company has rich experience on producing this kind of parts. If you have any needs, please feel free to contact us.

3. Aluminum Sheet Cushion
This part is a round piece with 2 square slots and some holes. It plays the role of a cushion in the machine. The part was stamped from the thin aluminum sheet. The accuracy of dimension can be guaranteed by die and process. The part surface is smooth and free of burrs. The raw material has a protective film to ensure that the surface will not be scratched. Such parts are widely used in industrial, commercial, and household products. Our technology and processing capabilities can fully meet customer requirements. We are confident to provide the parts with high-quality and reasonable price.

4. Stainless Steel Sheet Lid
The part is a round cover with a slender groove on the top surface and raised rim around it. The part is stamped from a high-gloss stainless steel sheet. The surface is very bright and smooth. There is a film on the raw material to protect the surface from scratching. The part is the appearance part of the product. Similar parts can be seen on many household products. Our stamping products are all customized by customers. Please contact us if you have the stamping part demand.

5. Deepdraw Round Cap
The shape of the part is hemispherical with protruding edges. It is drawn out of a cold-rolled steel sheet. In addition to blanking parts, our company also has rich processing experience in drawing parts. Over the years, we have provided customers with high-quality, low-price products with excellent services. The stamping parts produced by our company are all customized by customers. If you need stamping parts, please feel free to contact us.

Punched Parts
YRX Technology (Shenzhen) Co., Ltd. , https://www.yrx-tech.com